View CS4361_1061233.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CS4361 20-pin, 24-bit, 192 kHz, 6-channel D/A Converter
Features
Multi-bit Delta-sigma Modulator 24-bit Conversion Automatically detects sample rates up to 192 kHz. 105 dB Dynamic Range -95 dB THD+N Low Clock Jitter Sensitivity +3.3 V or +5 V Core Power +1.8 V to +5 V Interface Power Filtered Line Level Outputs On-chip Digital De-emphasis PopguardTM Technology Mute Output Control Small 20-pin TSSOP Package
I
Description
The CS4361 is a complete 6-channel digital-to-analog output system including interpolation, multi-bit D/A conversion, and output analog filtering in a small 20-pin package. The CS4361 supports all major audio data interface formats. The CS4361 is based on a fourth order, multi-bit, deltasigma modulator with a linear analog low-pass filter. This device also includes auto-speed mode detection using both sample rate and master clock ratio as a method of auto-selecting sampling rates between 2 kHz and 216 kHz. The CS4361 contains on-chip digital de-emphasis, operates from a single +3.3 V or +5 V power supply with separate built-in level shifter for the digital interface, and requires minimal support circuitry. These features are ideal for DVD players & recorders, digital televisions, home theater and set top box products, and automotive audio systems. ORDERING INFORMATION See page 20
Serial Audio Port & Control Supply (1.8 V to 5 V)
Analog & Digital Core Supply (3.3 V to 5 V)
Digital De-emphasis Level Translator Mode Control
Internal Voltage Reference
PCM Serial Audio Input
Auto-Speed Detecting PCM Serial Interface
6
Digital Filters
Multi-bit Modulators
Switch-Cap DAC and Analog Filters
6
Single-Ended Outputs (Six Channels)
+5 Volt-tolerant Reset
External Mute Control
Mute Control
Advance Product Information
http://www.cirrus.com
This document contains information for a new product. Cirrus Logic reserves the right to modify this product without notice.
Copyright (c) Cirrus Logic, Inc. 2005 (All Rights Reserved)
JAN `05 DS672A2
CS4361
Table 1. Revision History Release Date A1 January 2005 A2 January 2005 Changes Initial Release Correction to PDF file size.
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find one nearest you go to www.cirrus.com
IMPORTANT NOTICE "Advance" product information describes products that are in development and subject to development changes. Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners.
2
DS672A2
CS4361
TABLE OF CONTENTS
1. PIN DESCRIPTIONS ................................................................................................................ 4 2. CHARACTERISTICS AND SPECIFICATIONS ........................................................................ 5 Specified Operating Conditions ................................................................................................ 5 Absolute Maximum Ratings ...................................................................................................... 5 DAC Analog Characteristics ..................................................................................................... 6 DAC Analog Characteristics - All Modes .................................................................................. 6 Combined Interpolation & On-chip Analog Filter Response ..................................................... 7 Digital Input Characteristics ...................................................................................................... 8 Power & Thermal Characteristics ............................................................................................. 8 Switching Characteristics - Serial Audio Interface .................................................................... 9 3. TYPICAL CONNECTION DIAGRAM ..................................................................................... 11 4. APPLICATIONS ..................................................................................................................... 12 4.1 Master Clock .................................................................................................................... 12 4.2 Serial Clock ..................................................................................................................... 12 4.2.1 External Serial Clock Mode ................................................................................. 12 4.2.2 Internal Serial Clock Mode .................................................................................. 13 4.3 De-Emphasis ................................................................................................................... 15 4.4 Mode Select ..................................................................................................................... 15 4.5 Initialization and Power-Down ......................................................................................... 15 4.6 Output Transient Control ................................................................................................. 17 4.6.1 Power-up ............................................................................................................. 17 4.6.2 Power-down ........................................................................................................ 17 4.7 Grounding and Power Supply Decoupling ....................................................................... 17 4.8 Analog Output and Filtering ............................................................................................. 17 4.9 Mute Control .................................................................................................................... 18 5. PARAMETER DEFINITIONS .................................................................................................. 19 6. ORDERING INFORMATION .............................................................................................. 20 7. PACKAGE DIMENSIONS ...................................................................................................... 20 8. APPENDIX ......................................................................................................................... 21
DS672A2
3
CS4361
1. PIN DESCRIPTIONS
VL SDIN1 SDIN2 SDIN3 DEM/SCLK LRCK MCLK RST MODE FILT+
1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11
MUTEC AOUT1 AOUT2 AOUT3 AOUT4 VA GND AOUT5 AOUT6 VQ
Pin Name SDIN1 SDIN2 SDIN3 DEM/SCLK LRCK MCLK VQ FILT+ AOUT1 AOUT2 AOUT3 AOUT4 AOUT5 AOUT6 GND VA VL RST MUTEC MODE
# 2 3 4 5 6 7
Pin Description Serial Audio Data Input (Input) - Input for two's complement serial audio data.
De-emphasis/External Serial Clock Input (Input) - used for de-emphasis filter control or external serial clock input. Left Right Clock (Input) - Determines which channel, Left or Right, is currently active on the serial audio data line. Master Clock (Input) - Clock source for the delta-sigma modulator and digital filters.
11 Quiescent Voltage (Output) - Filter connection for internal quiescent voltage. 10 Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits. 19 Analog Output (Output) - The full scale analog output level is specified in the Analog Charac18 teristics specification table. 17 16 13 12 14 Ground (Input) - ground reference. 15 Analog Power (Input) - Positive power for the analog and core digital sections. 1 8 9 Interface Power (Input) - Positive power for the digital interface level shifters. Reset (Input) - Applies reset to the internal circuitry when low. Mode Control (Input) - Selects operational modes (see table 3).
20 Mute Control (Output) - Control signal for optional external muting circuitry.
4
DS672A2
CS4361
2.CHARACTERISTICS AND SPECIFICATIONS
All Min/Max characteristics and specifications are guaranteed over the specified operating conditions. Typical performance characteristics and specifications are derived from measurements taken at nominal supply voltage and TA = 25C.
SPECIFIED OPERATING CONDITIONS
AGND = 0 V; all voltages with respect to ground. Parameters DC Power Supply Symbol VA VA VL -CZZ -DZZ TA Min 4.75 3.0 1.7 -10 -40 Nom 5.0 3.3 3.3 Max 5.25 3.6 5.25 +70 +85 Units V V C C
Specified Temperature Range
ABSOLUTE MAXIMUM RATINGS
AGND = 0 V; all voltages with respect to ground. Parameters DC Power Supply Input Current, Any Pin Except Supplies Digital Input Voltage (pin 8, RST) Digital Input Voltage (all other digital pins) Ambient Operating Temperature (power applied) Storage Temperature Symbol VA VL Iin VIND VIND Top Tstg Min -0.3 -0.3 -0.3 -0.3 -55 -65 Max 6.0 VA 10 VA+0.4 VL+0.4 125 150 Units V V mA V V C C
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes.
DS672A2
5
CS4361
DAC ANALOG CHARACTERISTICS
Full-scale output sine wave, 997 Hz (Note 1), Fs = 48/96/192 kHz; Test load RL = 3 k, CL = 10 pF (see Figure 1). Measurement bandwidth is 10 Hz to 20 kHz, unless otherwise specified. 5 V Nom Parameter Dynamic Range 18 to 24-Bit 16-Bit Total Harmonic Distortion + Noise 18 to 24-Bit A-weighted unweighted A-weighted unweighted 0 dB -20 dB -60 dB 0 dB -20 dB -60 dB A-weighted unweighted A-weighted unweighted 0 dB -20 dB -60 dB 0 dB -20 dB -60 dB Min 99 96 90 87 95 92 86 83 Typ 105 102 96 93 -95 -82 -42 -93 -73 -33 105 102 96 93 -95 -82 -42 -93 -73 -33 Max -89 -76 -36 -87 -67 -27 -85 -72 -32 -83 -63 -23 Min 97 94 90 87 93 90 86 83 Dynamic Performance for CS4361-CZZ (-10 to 70C) 103 100 96 93 -95 -80 -40 -93 -73 -33 103 100 96 93 -95 -80 -40 -93 -73 -33 -89 -74 -34 -87 -67 -27 -85 -70 -30 -83 -63 -23 dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB 3.3 V Nom Typ Max Unit
16-Bit
Dynamic Performance for CS4361-DZZ (-40 to 85C) Dynamic Range 18 to 24-Bit 16-Bit Total Harmonic Distortion + Noise 18 to 24-Bit
16-Bit
Note:
1. One-half LSB of triangular PDF dither added to data.
DAC ANALOG CHARACTERISTICS - ALL MODES
Parameter Interchannel Isolation DC Accuracy Interchannel Gain Mismatch Gain Drift Analog Output Full Scale Output Voltage Quiescent Voltage Max DC Current draw from an AOUT pin Max Current draw from VQ Min AC-Load Resistance (see Figure 2 on page 8) Max Load Capacitance (see Figure 2) Output Impedance 6 VQ IOUTmax IQmax RL CL ZOUT 0.60*VA 0.65*VA 0.5*VA 10 100 3 100 100 0.70*VA Vpp VDC A A k pF DS672A2 0.1 100 0.25 dB ppm/C (1 kHz) Symbol Min Typ 100 Max Unit dB
CS4361
COMBINED INTERPOLATION & ON-CHIP ANALOG FILTER RESPONSE
The filter characteristics have been normalized to the sample rate (Fs) and can be referenced to the desired sample rate by multiplying the given characteristic by Fs. (See note 5) Parameter Combined Digital and On-chip Analog Filter Response Passband (Note 2) Frequency Response 10 Hz to 20 kHz StopBand StopBand Attenuation Group Delay De-emphasis Error (Note 4) Passband (Note 2) Frequency Response 10 Hz to 20 kHz StopBand StopBand Attenuation Group Delay Combined Digital and On-chip Analog Filter Response Passband (Note 2) Frequency Response 10 Hz to 20 kHz StopBand StopBand Attenuation Group Delay Notes: 2. Response is clock-dependent and will scale with Fs. 3. For Single Speed Mode, the measurement bandwidth is 0.5465 Fs to 3 Fs. For Double Speed Mode, the measurement bandwidth is 0.577 Fs to 1.4 Fs. For Quad Speed Mode, the measurement bandwidth is 0.7 Fs to 1 Fs. 4. De-emphasis is available only in Single Speed Mode. 5. Amplitude vs. Frequency plots of this data are available in "Appendix" on page 21. (Note 3) tgd to -0.1 dB corner to -3 dB corner (Note 3) tgd Fs = 44.1 kHz to -0.1 dB corner to -3 dB corner Combined Digital and On-chip Analog Filter Response (Note 3) tgd to -0.05 dB corner to -3 dB corner Symbol Min 0 0 -.01 .5465 50 0 0 -.05 .5770 55 0 0 0 0.7 51 Typ 10/Fs 5/Fs 2.5/Fs Max .4780 .4996 +.08 +.05/-.25 .4650 .4982 +.2 0.397 0.476 +0.00004 Unit Fs Fs dB Fs dB s dB Fs Fs dB Fs dB s Fs Fs dB Fs dB s Single Speed Mode
Double Speed Mode
Quad Speed Mode
DS672A2
7
CS4361
DIGITAL INPUT CHARACTERISTICS
Parameters High-Level Input Voltage -all input Pins except RST Low-Level Input Voltage -all input Pins except RST High-Level Input Voltage -RST pin (Note 6) Low-Level Input Voltage -RST pin Input Leakage Current Input Capacitance 7. Iin for LRCK is 20 A max. (% of VL) (% of VL) (% of VL) (% of VL) (Note 7) Symbol VIH VIL VIH VIL Iin Min 70% 90% Typ 8 Max 30% 10% 10 Units V V V V A pF
6. RST pin has an input threshold relative to VL but is VA tolerant.
POWER & THERMAL CHARACTERISTICS
5 V Nom Parameters Symbol Power Supplies Power Supply Current normal operation IA (Note 8) IL power-down state (Note 9) IA IL Power Dissipation normal operation power-down state (Note 9) Package Thermal Resistance JA Power Supply Rejection Ratio (Note 10) (1 kHz) PSRR (60 Hz) Min Typ 66 0.1 300 26 331 1.63 72 60 40 Max 90 1 455 Min 3.3 V Nom Typ 48 0.1 180 24 159 0.67 72 60 40 Max 63 1 211 Units mA mA A A mW mW C/Watt dB dB
8. Current consumption increases with increasing FS and increasing MCLK. Typ and Max values are based on highest FS and highest MCLK. Current variance between speed modes is small. 9. Power down mode is defined when all clock and data lines are held static. 10. Valid with the recommended capacitor values on VQ and FILT+ as shown in the typical connection diagram in Section 3.
125 Capacitive Load -- C L (pF) 100 75 50 25 Safe Operating Region
3.3 F AO U Tx R C V o ut
L
L
AG N D
2.5 3
5
10
15
20
Resistive Load -- RL (k )
Figure 1. Equivalent Output Test Load
Figure 2. Maximum Loading
8
DS672A2
CS4361
SWITCHING CHARACTERISTICS - SERIAL AUDIO INTERFACE
Parameters MCLK Frequency MCLK Duty Cycle Input Sample Rate (Note 11) All MCLK/LRCK ratios combined 256x, 384x, 1024x 256x, 384x 512x, 768x 1152x 128x, 192x 64x, 96x 128x, 192x Fs Symbol Min 0.512 45 2 2 84 42 30 50 100 168 45 tsclkl tsclkh tslrd tslrs tsdlrs tsdh (Note 12) (Note 13) tsclkw tsclkr tsdlrs tsdh tsdh 20 20 45 20 20 20 20 10 9 ---------------SCLK
Typ -
Max 50 55 216 54 134 67 34 108 216 216
Units MHz % kHz kHz kHz kHz kHz kHz kHz kHz % ns ns % ns ns ns ns % ns s ns ns ns
External SCLK Mode LRCK Duty Cycle (External SCLK only) SCLK Pulse Width Low SCLK Pulse Width High SCLK Duty Cycle SCLK rising to LRCK edge delay SCLK rising to LRCK edge setup time SDIN valid to SCLK rising setup time SCLK rising to SDIN hold time Internal SCLK Mode LRCK Duty Cycle (Internal SCLK only) SCLK Period SCLK rising to LRCK edge SDIN valid to SCLK rising setup time SCLK rising to SDIN hold time MCLK / LRCK =1152, 1024, 512, 256, 128, or 64 SCLK rising to SDIN hold time MCLK / LRCK = 768, 384, 192, or 96 50 50 50 55 55 -
10 9 --------------------- + 10 ( 512 )Fs 10 9 --------------------- + 15 ( 512 )Fs 10 9 --------------------- + 15 ( 384 )Fs
tsclkw ----------------2
-
Notes: 11. Not all sample rates are supported for all clock ratios. See table "Common Clock Frequencies" on page 12 for supported ratios and frequencies. 12. In Internal SCLK Mode, the duty cycle must be 50% 1/2 MCLK period. 13. The SCLK / LRCK ratio may be either 32, 48, 64, or 72. This ratio depends on data format and MCLK/LRCK ratio. (See figures 7-10)
DS672A2
9
CS4361
LRCK t slrd t slrs t sclkl t sclkh
SCLK t sdlrs
SDATA
t sdh
Figure 3. External Serial Mode Input Timing
LR C K
t s clkr
S D A TA t sclkw t sdlrs *IN TE R N AL S C L K t sdh
Figure 4. Internal Serial Mode Input Timing * The SCLK pulses shown are internal to the CS4361.
LRCK
MCLK
1 *INTERNAL SCLK N 2 N
SDATA
Figure 5. Internal Serial Clock Generation * The SCLK pulses shown are internal to the CS4361. N equals MCLK divided by SCLK
10
DS672A2
CS4361
3. TYPICAL CONNECTION DIAGRAM
+1.8 V to +5 V 1 VL 2 3 Audio Data Processor 4 5 6 SDIN1 SDIN2 SDIN3 DEM/SCLK LRCK AOUT1 AOUT2 AOUT3 AOUT4 AOUT5 AOUT6 19 18 17 16 13 12 20 15 VA 0.1 F
+ 1 F
+3.3 V to +5 V
Note*
3.3 F + 10 k C 470 Audio Output
Optional Muting Circuit
Rext
MUTEC CS4361 External Clock 7 MCLK
Controler
VL I2S LRCK MCLK RJ24 RJ16
8
Rext + 470 For best 20 kHz response 4Fs(Rext 470) Note* = This circuitry is intended for applications where the CS4361 connects directly to an unbalanced output of the design. For internal routing applications please see the DAC analog output characteristics for loading limitations. C= FILT+ 10 + 33 F
RST
9
MODE GND 14 VQ
11 0.1 F *3.3 F or *10 F
*Popguard ramp can be adjusted by selecting this capacitor value to be 3.3 F to give 250 ms ramp time or 10 F to give a 420 ms ramp time.
+
GND LJ
Figure 6. Recommended Connection Diagram
DS672A2
11
CS4361
4.APPLICATIONS
The CS4361 accepts data at standard audio sample rates including 48, 44.1 and 32 kHz in SSM, 96, 88.2 and 64 kHz in DSM, and 192, 176.4 and 128 kHz in QSM. Audio data is input via the serial data input pin (SDIN). The Left/Right Clock (LRCK) determines which channel is currently being input on SDIN, and the optional Serial Clock (SCLK) clocks audio data into the input data buffer.
4.1 Master Clock
MCLK/LRCK must be an integer ratio as shown in Table 2. The LRCK frequency is equal to Fs, the frequency at which words for each channel are input to the device. The MCLK-to-LRCK frequency ratio and speed mode is detected automatically during the initialization sequence by counting the number of MCLK transitions during a single LRCK period and by detecting the absolute speed of MCLK. Internal dividers are set to generate the proper clocks. Table 2 illustrates several standard audio sample rates and the required MCLK and LRCK frequencies. Please note there is no required phase relationship, but MCLK, LRCK, and SCLK must be synchronous.
LRCK 64x 96x 128x (kHz) 32 44.1 48 64 8.1920 88.2 11.2896 96 12.2880 128 8.1920 12.2880 176.4 11.2896 16.9344 22.5792 192 12.2880 18.4320 24.5760 Mode QSM
192x 12.2880 16.9344 18.4320 33.8680 36.8640
MCLK (MHz) 256x 384x 8.1920 12.2880 11.2896 16.9344 12.2880 18.4320 22.5792 33.8680 24.5760 36.8640 32.7680 49.1520 DSM
512x 22.5792 24.5760 32.7680 -
768x
1024x
1152x 36.8640 -
32.7680 33.8680 45.1580 36.8640 49.1520 49.1520 SSM
Table 2. Common Clock Frequencies
4.2 Serial Clock
The serial clock controls the shifting of data into the input data buffers. The CS4361 supports both external and internal serial clock generation modes. Refer to Figures 7-10 for data formats.
4.2.1 External Serial Clock Mode
The CS4361 will enter the External Serial Clock Mode when 16 low-to-high transitions are detected on the DEM/SCLK pin during any phase of the LRCK period. When this mode is enabled, the Internal Serial Clock Mode and de-emphasis filter cannot be accessed. The CS4361 will switch to Internal Serial Clock Mode if no low-to-high transitions are detected on the DEM/SCLK pin for two consecutive frames of LRCK. Refer to Figure 12.
12
DS672A2
CS4361
4.2.2 Internal Serial Clock Mode
In the Internal Serial Clock Mode, the serial clock is internally derived and synchronous with MCLK and LRCK. The SCLK/LRCK frequency ratio is either 32, 48, 64, or 72 depending upon data format. Operation in this mode is identical to operation with an external serial clock synchronized with LRCK. This mode allows access to the digital de-emphasis function. Refer to Figures 7 - 12 for details.
LR C K SCLK
Le ft C ha n nel
R ig h t C ha n nel
SDATA
MSB -1 -2 -3 -4 -5
+5 +4 +3 +2 +1 LSB
MSB -1 -2 -3 -4
+5 +4 +3 +2 +1 LSB
Internal SCLK Mode I S, 16-Bit data and INT SCLK = 32 Fs if MCLK/LRCK = 1024, 512, 256, 128, or 64 I2S, Up to 24-Bit data and INT SCLK = 48 Fs if MCLK/LRCK = 768, 384, 192, or 96 I2S, Up to 24-Bit data and INT SCLK = 72 Fs if MCLK/LRCK = 1152
2 2
External SCLK Mode I S, up to 24-Bit Data Data Valid on Rising Edge of SCLK
Figure 7. CS4361 Data Format (I2S)
LR C K SCLK
Le ft C ha n nel
R ig h t C ha n nel
SDATA
M SB -1 -2 -3 -4 -5
+5 +4 +3 +2 +1 LS B
M SB -1 -2 -3 -4
+5 +4 +3 +2 +1 LS B
Internal SCLK Mode Left Justified, up to 24-Bit Data INT SCLK = 64 Fs if MCLK/LRCK = 1024, 512, 256, 128, or 64 INT SCLK = 48 Fs if MCLK/LRCK = 768, 384, 192, or 96 INT SCLK = 72 Fs if MCLK/LRCK = 1152
External SCLK Mode Left Justified, up to 24-Bit Data Data Valid on Rising Edge of SCLK
Figure 8. CS4361 Data Format (Left Justified)
DS672A2
13
CS4361
R igh t C h ann el
LR C K
Le ft C ha n nel
SCLK
SDATA
0
23 22 21 20 19 18
7
6
5
4
3
2
1
0
23 22 21 20 19 18
7
6
5
4
3
2
1
0
Internal SCLK Mode Right Justified, 24-Bit Data INT SCLK = 64 Fs if MCLK/LRCK = 1024, 512, 256, 128, or 64 INT SCLK = 48 Fs if MCLK/LRCK = 768, 384, 192, or 96 INT SCLK = 72 Fs if MCLK/LRCK = 1152
32 clocks
External SCLK Mode Right Justified, 24-Bit Data Data Valid on Rising Edge of SCLK SCLK Must Have at Least 48 Cycles per LRCK Period
Figure 9. CS4361 Data Format (Right Justified 24)
LR CK
L e ft C h a nn e l
R ig ht C h a n ne l
SCLK
SDATA
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
Internal SCLK Mode 32 clocks Right Justified, 16-Bit Data INT SCLK = 32 Fs if MCLK/LRCK = 1024, 512, 256, 128, or 64 INT SCLK = 48 Fs if MCLK/LRCK = 768, 384, 192, or 96 INT SCLK = 72 Fs if MCLK/LRCK = 1152
External SCLK Mode Right Justified, 16-Bit Data Data Valid on Rising Edge of SCLK SCLK Must Have at Least 32 Cycles per LRCK Period
Figure 10. CS4361 Data Format (Right Justified 16)
14
DS672A2
CS4361
4.3 De-Emphasis
The CS4361 includes on-chip digital de-emphasis. Figure 11 shows the de-emphasis curve for Fs equal to 44.1 kHz. The frequency response of the de-emphasis curve will scale proportionally with changes in sample rate, Fs. The de-emphasis filter is active (inactive) if the DEM/SCLK pin is low (high) for five consecutive falling edges of LRCK. This function is available only in the internal serial clock mode when LRCK < 50 kHz.
Gain dB T1=50 s 0dB
T2 = 15 s
-10dB
F1 3.183 kHz
F2 Frequency 10.61 kHz
Figure 11. De-Emphasis Curve (Fs = 44.1kHz)
4.4 Mode Select
Mode selection is determined by the Mode Select pin. The value of this pin is locked 1024 LRCK cycles after RST is released. This pin requires a specific connection to supply, ground, MCLK, or LRCK as outlined in table 3. . Mode pin is: Tied to VL Tied to GND Tied to LRCK Tied to MCLK Mode I2S Left Justified Right Justified - 24 bit Right Justified - 16bit Table 3. Mode pin settings Figure 7 8 9 10
4.5 Initialization and Power-Down
The initialization and power-down sequence flow chart is shown in Figure 12. The CS4361 enters the power-down state upon initial power-up. The interpolation filters and delta-sigma modulators are reset, and the internal voltage reference, multi-bit digital-to-analog converters, and switched-capacitor low-pass filters are powered down. The device will remain in the power-down mode until RST is released and MCLK and LRCK are present. Once MCLK and LRCK are detected, MCLK occurrences are counted over one LRCK period to determine the MCLK/LRCK frequency ratio. Power is then applied to the internal voltage reference. Finally, power is applied to the D/A converters and switched-capacitor filters, and the analog outputs will ramp to the quiescent voltage, VQ.
DS672A2
15
CS4361
USER: Apply Power
VQ and outputs ramp down
Power-Down State
VQ and outputs low
VQ and outputs ramp down
USER: Apply MCLK, release RST USER: Apply RST VQ and outputs ramp up USER: Apply RST
USER: Remove LRCK or MCLK
Wait State
USER: Remove LRCK or MCLK
USER: Apply LRCK and MCLK
USER: change MCLK/LRCK ratio
MCLK/LRCK Ratio Detection
USER: change MCLK/LRCK ratio
USER: No SCLK
USER: Applied SCLK
SCLK mode = internal
SCLK mode = external
Normal Operation De-emphasis available
Normal Operation De-emphasis not available
Analog Output is Generated
Analog Output is Generated
Figure 12. CS4361 Initialization and Power-Down Sequence
16
DS672A2
CS4361
4.6 Output Transient Control
The CS4361 uses PopguardTM technology to minimize the effects of output transients during power-up and powerdown. When implemented with external DC-blocking capacitors connected in series with the audio outputs, this feature eliminates the audio transients commonly produced by single-ended, single-supply converters. To make best use of this feature, it is necessary to understand its operation.
4.6.1 Power-up
When the device is initially powered-up, the audio outputs, AOUT1-6 are clamped to VQ which is initially low. After RST is released and MCLK is applied, the outputs begin to ramp with VQ towards the nominal quiescent voltage. This ramp takes approximately 200 ms to complete. The gradual voltage ramping allows time for the external DC-blocking capacitors to charge to VQ, effectively blocking the quiescent DC voltage. Audio output begins approximately 2000 sample periods after valid LRCK and SDIN are supplied (and SCLK, if used).
4.6.2 Power-down
To prevent audio transients at power-down, the DC-blocking capacitors must fully discharge before turning off the power. In order to do this RST should be held low for a period of about 250 ms before removing power. During this time voltage on VQ and the audio outputs discharge gradually to GND. If power is removed before this 250 ms time period has passed a transient will occur when the VA supply drops below that of VQ. There is no minimum time for a power cycle, power may be re-applied at any time. When changing clock ratio or sample rate it is recommended that zero data (or near zero data) be present on SDIN for at least 10 LRCK samples before the change is made. During the clocking change the DAC outputs will always be in a zero data state. If non-zero audio is present at the time of switching, a slight click or pop may be heard as the DAC output automatically goes to its zero data state.
4.7 Grounding and Power Supply Decoupling
As with any high resolution converter, the CS4361 requires careful attention to power supply and grounding arrangements to optimize performance. Figure 6 shows the recommended power arrangement with VA connected to a clean +3.3 V or +5 V supply. For best performance, decoupling and filter capacitors should be located as close to the device package as possible, with the smallest capacitors placed closest.
4.8 Analog Output and Filtering
The analog filter present in the CS4361 is a switched-capacitor filter followed by a continuous-time, low-pass filter. Its response, combined with that of the digital interpolator, is given in Figures 14 - 21. The recommended external analog circuitry is shown in the "Typical Connection Diagram" on page 11. The analog outputs are named AOUT1-6. The SDIN1 feeds AOUT1 as the `Left' marked data and AOUT2 as the `Right' marked data. The SDIN2 feeds AOUT3 as the `Left' marked data and AOUT4 as the `Right' marked data. The SDIN3 feeds AOUT5 as the `Left' marked data and AOUT6 as the `Right' marked data.
DS672A2
17
CS4361
4.9 Mute Control
The MUTEC pin is intended to be used as control for an external mute circuit in order to add off-chip mute capability. This pin becomes active under the following conditions. 1) during power-up initialization 2) upon reset 3) if the MCLK to LRCK ratio is incorrect 4) upon receipt of 8192 consecutive samples of zero 5) during power-down. The MUTEC pin will only go active on static zero data only if all 6 channels satisfy the 8192 sample requirement. If any channel receives non-zero data then the mute pin will return low (inactive). Use of the mute control function is not mandatory but is recommended for designs requiring the absolute minimum in extraneous clicks and pops. Also, use of the mute control function can enable the system designer to achieve idle channel noise & signal-to-noise ratios which are only limited by the external mute circuit. The MUTEC pin is an active-high CMOS driver. See Figure 13 below for a suggested active-high mute circuit.
AC Couple AO UT
470 Filter Cap
6
10 k
A udio O ut 47 k
C S 4361 +V A MMU N 2111LT1 2 k MU TE C 10 k MMU N 2211LT1 -V
(if a va ila ble ) (Low R on)
6
Figure 13. Suggested Active-low Mute Circuit
18
DS672A2
CS4361
5.PARAMETER DEFINITIONS
Total Harmonic Distortion + Noise (THD+N) The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Dynamic Range The ratio of the full scale rms value of the signal to the rms sum of all other spectral components over the specified bandwidth. Dynamic range is a signal-to-noise measurement over the specified bandwidth made with a -60 dBFS signal. 60 dB is then added to the resulting measurement to refer the measurement to full scale. This technique ensures that the distortion components are below the noise level and do not effect the measurement. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991, and the Electronic Industries Association of Japan, EIAJ CP-307. Interchannel Isolation A measure of crosstalk between the left and right channels. Measured for each channel at the converter's output with all zeros to the input under test and a full-scale signal applied to the other channel. Units in decibels. Interchannel Gain Mismatch The gain difference between left and right channels. Units in decibels. Gain Error The deviation from the nominal full scale analog output for a full scale digital input. Gain Drift The change in gain value with temperature. Units in ppm/C.
DS672A2
19
CS4361
6.ORDERING INFORMATION
Model CS4361-CZZ CS4361-DZZ Temperature -10 to +70 C -40 to +85 C Package 20-pin Plastic TSSOP - Lead-Free 20-pin Plastic TSSOP - Lead-Free
7.PACKAGE DIMENSIONS
20L TSSOP (4.4 mm BODY) PACKAGE DRAWING
N
D
E11 A2 A1
L
E
A
e b2 SIDE VIEW
123
END VIEW
SEATING PLANE
TOP VIEW
INCHES DIM A A1 A2 b D E E1 e L MIN -0.002 0.03346 0.00748 0.252 0.248 0.169 -0.020 0 NOM -0.004 0.0354 0.0096 0.256 0.2519 0.1732 -0.024 4 MAX 0.043 0.006 0.037 0.012 0.259 0.256 0.177 0.026 0.028 8 MIN -0.05 0.85 0.19 6.40 6.30 4.30 -0.50 0
MILLIMETERS NOM --0.90 0.245 6.50 6.40 4.40 -0.60 4 MAX 1.10 0.15 0.95 0.30 6.60 6.50 4.50 0.65 0.70 8
NOTE
2,3 1 1
JEDEC #: MO-153 Controlling Dimension is Millimeters. Notes: 1. "D" and "E1" are reference datums and do not included mold flash or protrusions, but do include mold mismatch and are measured at the parting line, mold flash or protrusions shall not exceed 0.20 mm per side. 2. Dimension "b" does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be 0.13 mm total in excess of "b" dimension at maximum material condition. Dambar intrusion shall not reduce dimension "b" by more than 0.07 mm at least material condition. 3. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips.
20
DS672A2
CS4361
8.APPENDIX
Figure 14. Single Speed Stopband Rejection
Figure 15. Single Speed Transition Band
Figure 16. Single Speed Transition Band
Figure 17. Single Speed Passband Ripple
DS672A2
21
CS4361
Figure 18. Double Speed Stopband Rejection
Figure 19. Double Speed Transition Band
Figure 20. Double Speed Transition Band
Figure 21. Double Speed Passband Ripple
22
DS672A2
CS4361
0
0
-10
-10
-20
-30
-20
-40 Amplitude (dB)
Amplitude (dB) -30
-50
-60
-40
-70
-50
-80
-60
-90
-100 0 0.1 0.2 0.3 0.4 0.5 0.6 Frequency(normalized to Fs) 0.7 0.8 0.9 1
0.35 0.4 0.45 0.5 0.55 0.6 Frequency(normalized to Fs) 0.65 0.7 0.75
Figure 22. Quad Speed Stopband Rejection
Figure 23. Quad Speed Transition Band
0 0.2 -5 0.15 -10 -15 -20 -25 -30 -35 -0.1 -40 -0.15 -45 -0.2 -50 0.4 0.45 0.5 0.55 0.6 Frequency(normalized to Fs) 0.65 0.7 0.05 0.1 0.15 0.2 0.25 0.3 Frequency(normalized to Fs) 0.35 0.4 0.45 0.1
0.05 Amplitude (dB)
Amplitude (dB)
0
-0.05
Figure 24. Quad Speed Transition Band
Figure 25. Quad Speed Passband Ripple
DS672A2
23

▲Up To Search▲

Price & Availability of CS4361

	To Download CS4361 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .